Skip to Content

Category Archives: Tips

Attic Ventilation Tips By Gil Strachan

With regard to summer cooling, I was prompted to peck out a few words on attic ventilation. In addition to keeping us warm, and preventing condensation & mildew in the winter, an adequately insulated and ventilated attic space will reduce the summer heat load in living spaces. A well ventilated attic will function much like a big shade tree! The general rule of thumb is “one square foot of unobstructed ventilation area for every 300 square feet of ceiling space; no less that 50% of the total inbound through the soffits or gable vents, and no more than 50% outbound via roof or ridge vents. The bird and bug screens can diminish the effectiveness of the vents by as much as 50%, so double this amount.

For example, a 1500 sq. ft house requires a minimum of 5 sq. ft of unobstructed ventilation area (min. 10 sq. ft. of screened vent area). This would likely be accomplished with 5 (1 sq ft) roof vents (or a larger number of smaller vents) and in most new homes, a continuous vented soffit covering. In older homes with wooden soffit coverings incorporating individual soffit vents, subsequent covering with vented aluminum will drastically impede air flow through the original openings. The wood soffit covering should be removed prior to installation of the aluminum soffit covering. If aluminum has already been applied over plywood, temporarily remove this covering to introduce more openings into the wooden soffits.

To determine whether or not your attic is adequately ventilated, first survey the number of roof vents. Then lift the access hatch inside the house (usually found in a closet or hallway ceiling). If the attic temperature is extremely high, especially on a cooler day, this means heat-loaded air is not being sufficiently vented. Also, you may notice a rush of air entering up through the access hatch. This means you might have enough roof vents, but not enough soffit (or gable) vents. The relative heights of roof versus gable vents will also be a determining factor. The higher the roof vents are above the gable vents, the more effectively the attic will ventilate.

A minimum of R20 (approx. 8”) of insulation over the upper floor ceilings is required to effectively isolate the attic from the living spaces, and continuous vapor barriers behind walls and ceilings will stop infiltration of hot outside air, and exfiltration of cooler (hopefully) inside air. Check that your soffit vents are not obstructed by insulation materials.

Without air conditioning, it helps to open all the windows overnight, and then shut down the house and close the window coverings all day, just like grandmother did it! Aluminum foil, or commercially available tinting, can also help when applied to south and west-facing windows.

 

Six Wonderful Tips For Avoiding The Cost of Professional Roof Service

Roofing bad shape

About Author…

Copyright Gil Strachan – All rights reserved.Gil Strachan is a professional home inspector, representing Electrospec Home Inspection Services in east-central Ontario since 1994. For more information about home inspections visithttp://www.electrospec.ca

 

READ MORE

Remove the Complex From Cost-Efficient Roof Replacement

If anyone ever claimed that cost-efficient roof replacement is simple, turn your back and head in the other direction. Getting the best pricing while still ensuring quality roof installation doesn’t mean that you opt for the cheapest Charlotte roofing contractor and the lease expensive roofing materials. It just means that you must do your homework.

In any home improvement venture, making the most of your money demands that you inject personal time and energy into the project. Knowing what to expect in costs and services provides you with access to cost-efficient Charlotte roofing. Twelve years ago, according to the U.S. Census Bureau, roofing contractors spent over 8-million dollars on components, fuels, materials and supplies (1). During the first eleven months of 2013, construction spending exceeded $828 billion (2). Residential construction accounted for $345 billion.

Home improvement defines the term “competitive.” Low-ball roofing service centers dot the industry. Poor craftsmanship further compromised by second-hand roofing materials leave many Charlotte homeowners in the financial pinch of an inefficient roofing job. Cost-efficient roof replacement is available but sometimes difficult to grasp.

The following simple tips establish the guidelines for quality-roofing services using top-of-the-line materials and roof replace cost-efficient contractors.

Locating a Quality Charlotte Roofing Contractor

Roof replacement is not cheap. If you are looking for a ‘cheap’ roofing contractor, this is the wrong website. However, you can find a Charlotte roofing contractorwho is able to provide durable and cost-efficient roof replacement. The search involves three schools of thought:

  • Old School – Looking in the newspapers and the yellow pages
  • New School – Digging into the abundance of information available on the Internet
  • Decision School – Closing via reliable referrals.

Small businesses dominate the home improvement industry. Most of these will fail within the first three years of business. According to the Small Business Administration, small business failure occurs for the following reasons (3):

  • Insufficient capital
  • Lack of experience
  • Low sales
  • Misuse of business funds
  • Poor location
  • Poor service
  • Superior competition
  • And More.

When searching for a Charlotte roofing contractor, apply all three methods. Be careful of super-sized newspaper ads, Internet sites that serve only to promote roofing companies and on-site referrals. Many web-based “Yellow Pages” and “Service Referral” sites claim to be impartial. According to the Bureau of consumer Protect, business directory scams litter the Internet (4). Business payments to so-called unbiased Internet advertising sites make the scam possible. So ask yourself how the so-called “expert” finders stay in business without having what is typically called a “premium” advertiser list.

The best resource for finding a reputable roofing company comes via the referral you get from someone you trust. Back that up by investigating how long a business has been in operation, and various other business reports. Finding the Internet age of a business is as simple as typing:

whois http://zimmermanenterprises.com or any other business name. The “Whois” report supplies you with a domain creation date as well as various ownership details.

Interviewing Roof Installation Contractors

During any interview process, learn to Watch out for that “gut” feeling. Interviews are designed to educate buyers and instill trust for the roofing company. The “gut” feeling can be positive or negative. But remember: for you the interview is about information, finding what meets your roofing needs and getting cost-efficient roofing replacement from a quality company. Don’t permit a “gut” feeling to blind your common sense.

Trust is indeed a major concern. What begins with a “gut” impulse must be reinforced by:

  • Presentation of a building license
  • Evidence of insurance and bonding
  • Membership in professional trade organizations
  • And a host of satisfied customers.

 

READ MORE

Clogged Gutters, Leaky Faucets, and Other Mosquito-Favorable Environments

Mosquito prevention: the core process that helps avoid the risk of West Nile virus and other mosquito-related infections. Although any time of day can be mosquito time, dusk and dawn mark the typical danger zone. When untreated water accumulates, so too do the bloodsuckers that help spread the viruses. For female mosquitoes, calm air opens the window of opportunity for biting humans. Successful prevention of the “little fly,” as the word means in Spanish, requires that you eliminate and/or reduce the breeding pits. However, spotting standing water is not always easy. Water that accumulates due to clogged gutters, under-the-house A/C drippings, and even a leaky downspout can be difficult to notice.

Anywhere that untreated water meets mosquito-favorable weather conditions the bugs will breed. In a nation populated by around 175 various species of “little flies,” homeowners in Charlotte, NC and neighboring cities run a bold risk of infestation. The bugs lack teeth in the sense of other biting critters, but they do have a “proboscis.” This long, pointed mouth-part helps the female of the species pierce a victim’s skin, locate a suitable capillary, and then suck blood at a rate of up to three times the mosquitoes body weight.

Clogged Gutters, A Life Support System For Blood Sucking Devils

The typical female “little fly,” also called “Mozzies” whether male or female, can lay up to 300 eggs at a single dropping. Deposited in “rafts” or clusters if you prefer clearer understanding, the eggs may be dropped onto the surface of stagnant water. However, they are also sometimes laid in a standard flood path. Hatching takes place in as little as one inch of untreated water. And that old female, that bitter and breeder, well… she can drop eggs up to three times before she dies.

They normally thrive for ten days before ready to leave the water. For mosquitoes, life begins as larvae, often called a “wiggler.” And although birthed and thriving in stagnant water, wigglers breathe surface oxygen. In time, they develop into pupae. Whereas the wigglers feed off the organic matter that accumulates in stagnant water, the pupae are partially cocoon-cased. Thus they need no food. After a few days in the pupae state, the bug exits as a full-grown adult bloodsucker. Thankfully the typical female mossie lifespan is but two months – males usually only life 10 days or so. However, hibernating females can live up to six months.

Clogged gutters, toys, and junk piles are among the many places where mosquito life-support is readily available. Junk piles are easy to see. Toys, old tires and planter buckets are typically easy cleans. However, gutters clogged can be more difficult to notice. One test: when rain comes, check for gutter overflow. Unless your system is undersized for your home, gutter overflow should be relatively non-existent.

Preventing Mossie Accumulation – Eighteen Tips

Being cold-blooded bugs, mosquitoes hibernate. When Charlotte regional temperatures drop below 50 degrees, the adults are ready for bed. Sometimes rather than hibernate, a female mossie lays eggs in freezing water and then simply dies. The cold water doesn’t prevent the birth cycle. When warm weather returns, the eggs hatch. So winter, spring, summer or fall, applying the following eighteen defensive methods will help rid your home of mosquito infections.

1. Eliminate the junk
2. Cover the trash container
3. Clean gutters
4. Keep up with the swimming pool
5. Unblock the storm drains
6. Ensure solid runoff around the downspouts

7. Eliminate water accumulation in the crawl space
8. Clean up the bird baths
9. Check the saucers around potted plants
10. Set small boats, canoes and kayaks top down
11. Check the air conditioning air handler run-off and drain pan
12. Seal cracked or broken concrete slabs
13. Make sure the ground beneath your deck is properly drained
14. Install caps on any open fence posts
15. Control home irrigation so as to prevent excessive water detainment
16. Install and/or repair window screens and vent screens in the attic or the crawlspace
17. Repair any leaky faucets outside as well as inside your home
18. Call Right Way Exterior Solutions for installation of an efficient and effective gutter guard system.

For gutter cleaning, now may be your best time to respond. We’re pushing for this business, seeking to provide quality and timely prevention of clogged gutters in homes anywhere within our range of service. Or, perhaps your Charlotte regional home has suffered from storm damage. If so… Call now for a FREE roof inspection by the professionals at Right Way Exterior Solutions, LLC. We will work for your business.

Final note:

According to the author of “Mosquito Facts – 33 Things You Didn’t Know About Mosquitoes,” bug zappers are no help in the prevention of mosquitoes (1). More often than not, such devices kill harmless and even beneficial insects – but very few bugs that bite.

1) http://www.megacatch.com/mosquitofacts.html

READ MORE

Seasonal Attention Prevents Roof Problems Charlotte

Although many roof problems are easy to fix they are typically ignored until damage has accumulated into a costly Charlotte roof repair expense. Sure. Addressing household maintenance issues can be a pain. However, if your fail to give your Charlotte roof seasonal attention, you may be permitting a minor roof failure to expand into a full-fledged water problem. Yet simple seasonal roof maintenance can prevent so much cost, waste and internal home damage.

The following list is not a self-diagnostic roofing repair guide. It is, however, an informative list of roof problems that are most common causes of roof failure:

1) Substandard Installation

Being a highly engineered construction means that your Charlotte roof has many points where failure can occur. Reputable roofing contractors know and follow the roof construction standards and laws appropriate to the Charlotte Metro regional home system.

2) Lack of Flashing

Flashing is essential to creating a reliable roofing system. However, some Charlotte roofing contractors have been know to save money by ignoring the need for installed flashing. Don’t get caught with your flashing off.

3) Roof leaks and moisture

Roof leaks can occur for a number of reasons. Sometimes it has to do with a lack of flashing, a nail in the wrong spot, or even a built-up roof (BUR) that your Charlotte roof installer failed to fasten properly. Your seasonal roof inspection should include examination of any point where moisture infiltration has occurred.

4) Use of Mismatched MaterialsIce dams on a Slate roof

It’s a sad thing, but some home improvement contractors have no sense of aesthetic shingle, metal and tile matching concepts. But mismatching roof materials involves even more that looks and curb appeal. Certain mismatched roofing components such as copper and iron can even promote radically quicker deterioration of your roof. Thus, roof failure becomes an early certainty. Quality roof service contractors don’t make such foolish mistakes.

5) Third-Party Damage

Look out for and check behind third-party vendors. If the satellite man or the siding contractor damages your roof, you need to catch the damage early. Immediately behind such services, you should schedule a roof maintenance checkup. Why pay for a roof failure that belongs in the expense bucket of the cable provider?

6) No Preventative Maintenance

Be it a car engine or be it your Certainteed roof shingles, lack of preventative maintenance is a primary reason for product failure. This is a worthwhile investment: Have a professional Charlotte roofing contractor walk your roof once per year. Early spotting and fixing of potential roof problems is much less costly than replacing the underlying wood framework.

7) Blow-Offs, Tenting, Reduced Wind Uplift Resistance, And Billowing

Leakage is only one aspect of incorrectly installed roof flashing. On hot-bituminous roofs, poorly installed flashing can result in gaping seams and faulty laps. The end result: blow-offs, code violations, and damage due to an ineffective puncture resistance. Likewise on torch-applied mod bit roof systems as well as hot-bituminous roofs, ineffective gravel embedment coupled with inadequate use of fasteners in the base sheet can result in excessive roof failure. .

8) Poor Installation And Unsatisfactory Workmanship

Roof installation – a work of crucial beginnings. You pay good money for a quality roofing product and a supposed reliable installation job. The life expectancy of the product is 30 to 50 years – if correctly installed. Seek proven quality workmanship. Ask for documentation on bonding, insurance and licensing. Investigate the references. And get your guarantee in writing.

9) Improper Repairs

Many roof failures are a direct result of application of materials not designed for a specific type of roof. Professional Charlotte roofers know the distinctions between components necessary for repairing an asphalt-shingled roof versus a metal roof. Likewise it is with other roofing materials. Using improper roofing repair components are at best, a temporary solution, and at worse can make the prevailing roofing problem even more severe.

10)

Ponding Water

raindrop background plugWater that cannot runoff in the conventional manner eventually seeps through all obstacles so that internal home damage is the only outlet. If your failed roofing system includes ponding water, find the cause before fixing the leakage.

11) Shrinkage And Blistering

Blistering and delamination often accompany spray polyurethane foam installation over wet substrate. Even if a blister is not worth fixing, trained roofers understand the symptomatic roofing problems associated with BUR systems. Blistering, ridging, splitting and surface erosion may not demand critical attention, but yourCharlotte roofing contractor most know the when and the how of any given situation.

12) Shingle Deterioration

Worn shingles tend to curl, split and decline in efficient water repelling effectiveness. Structural rot and interior home damage will soon follow suit. Catching the situation before the signs of roof failure become apparent to the casual observer will almost always reduce the cost for roof repair.

Right Way Exterior Solutions – Fixing Your Charlotte Roofing Problems Today

For professional, timely, and reasonably priced home roof installation or home roof repairs, contact Mark Zimmerman at Right Way Exterior Solutions (mark@zimmermanenterprises.com). Ensuring a quality installation or repair is our job. Ensuring that your Charlotte home roof receives yearly maintenance is your job. Early detection of roofing problems saves your home from excessive damage due to a failed roofing system.

 

READ MORE

Accidental Electrocution Listed In OSHA 2013 “Fatal Four” Report

In order to avoid accidental electrocution during home roof repairs, homeowners should learn and follow OSHA warnings pertaining to electrical safety. Whether repairing a roof leak or repairing a leak related electrical problem, learn the associated risks and avoid watts of pain.

Troubleshooting electrical systems is always risky. Factor in the possibility of accumulate water from a leaky roof, and the possibilities of electrical shock takes a sharp upward spike. According to the 2013 OSHA construction “Fatal Four” report, 8.6% out of 828 total 2013 construction-related deaths were by cause of electrocutions (1). Furthermore, three hundred and two of those deaths were due to falls – some of which were triggered by an electrical shock.

Not all electrical accidents result in death, but a lasting scar or a disabling wound can induce a similar type of extended family trauma. So… If you are not sure how to avoid accidental electrocution during a roofing installation or roof repair project, consider leaving the task in the hands of professional roofers.

Electricity, Dangerous On or Off the Roof

Although sometimes connected via underground cable, electricity typically enters homes through a lead wire that suspends between the eaves of the roof and a nearby utility pole. In either event, careless handling of electrical wires and components can result in serious electrical shock.

For roofers the risk of accidental contact with exposed electrics is a daily job hazard. Working with hammers, nails, ladders and other metal work tools proportionally increases the chances of an avoidable electrical accident. Even taking handhold on a metal gutter can result in an unexpected discovery: somewhere around the corner, that very gutter system may be in contact with an open and live wire.

Other electrical hazards include:

  • A improperly grounded roof antennae or TV dish
  • A shorted roof-mounted air conditioning unit
  • And even a collection of water that links to shorted outlet in the attic.

How to Avoid Accidental Electrocution

Sometimes the wires around a roof get old, worn and exposed to destructive weather elements. It doesn’t take much to let injurious energy into the roofer’s world. Furthermore, not all home electricians perform their duties with care. It is possible that even in a brand new home, the electrician to correctly install the electrical system. This can mean that even a roofing nail could penetrate a hidden electric line.

Water leaking into an attic electrical outlet can also result in serious roofer injury. So, if you have any concerns about the electrics in your home, consider having a professional electrician come out for a wiring check.

Shutting down power at the c-panel box eliminates most of the risk factor. And, if necessary, your local power company will gladly come out and disconnect the lead line into the house if necessary. But remember also that certain appliances store energy in on-board capacitors. Thus even a dead lead line is not absolute assurance that all dangers are removed.

Specifics of Outdoors Electric Wiring

Although performing the same primary function, outdoor electrical cables are constructed differently than interior cables. According to electrical installation standards released by the National Electrical Manufacturers Association, and adopted in one form or another by all U.S. states, the code for outdoor wiring is slightly different than the code for indoor wiring (2). Although not all states apply the same measure of NEMA standards, many communities do require a a licensed electrician for outdoor wiring projects. However, some regions merely demand that a licensed pro handle the final inspection of a finished electrical project.

What makes outdoor wiring different? Outdoor wiring needs protection from the elements. It is subjected to wet and icy conditions, drastic changes in temperature, and corrosion. Also, overhead cables must be kept high enough to avoid posing a hazard to ground traffic. Generally a height of 12 feet is adequate for residential work, but not always practical, and does nothing to guard against dangers such as falling trees, limbs and swinging ladders.

Weatherproofing Outdoor Electrics

Outdoors electrical materials and equipment such as fixtures, electrical boxes, receptacles, connectors, and fittings are manufactured not only to meet code requirements but also as resistant to the elements. Outdoors electrical equipment must be weatherproof and sometimes fully weather-tight as well.

 

Right Way Exterior Solutions – Doing the Hard Work For You

Avoid accidental electrocution and any other hazard associated with residential roofing. Call Right Way Exterior Solutions.

READ MORE

Value-added Charlotte Exterior Solutions At Reasonable Prices

Buying a new roof in Charlotte, replacing the roof on an older Charlotte home, or upgrading worn siding is one of the most important investments a Charlotte homeowner can make. Yourroofing and gutter system protects your home and family. Vinyl siding eliminates painting while adding curb appeal at the same time. You should take as much care in selecting a Charlotte Roofing contractor, gutter guard provider, or siding installer as you would with any other important home or business decision.

 

Let An Straight-Up Charlotte Roofing Contractor Repair or Replace The Shingles On Your Home or Business

Many Charlotte Roofing Contractors do not perform roof repairs. Their warranties often depend upon installation of a brand new Charlotte roof. But your budget or the actual problems with your roof may have not require the installation of a new roof. You need a Charlotte Roofing Contractor who places you and your family ahead of higher profits and greater job turn-around. At Right Way Exterior Solutions, LLC Charlotte contractor services, we inspect your home or business using our personally developed roof inspection plan. Trained to find all of the issues associated with Charlotte roof repairing or Charlotte roof replacement, we help you determine the best solution to your specific home or business roofing needs. A careful Charlotte roof inspection helps prevent problem coverups that can cause high-dollar future complications.

You take home and roof seriously. So do we.

Right Way Exterior Solutions, LLC does Charlotte roof repairs, Charlotte roof replacements and new Charlotte roofing installations for a living. As a Value-Added Charlotte Exterior Solutions Contractor, we know and understand the local weather conditions, the yearly climate changes and the local zoning laws. We understand how these issues relate to your home’s roof. But even more than that, Mark Zimmerman is also a Piedmont area homeowner. He has lived in the Charlotte area for over fifty years. He knows the hazards that your Charlotte roofing system must endure. He employees local roofers who also understand the environmental conditions around Mount Holly, Stanley, Iron Station and other Charlotte areas. These professional Charlotte Roofers know how local conditions affect Charlotte roofing materials and Charlotte roofing installation practices. The Zimmerman roofing team knows how to remain focused on quality roof construction and waterproofing. Right Way Roofing & More, LLC represents professional home and business roofing services. Mark Zimmerman represents Right Way Roofing & More, LLC quality. We are dedicated to providing the best available roofing services throughout the area.

READ MORE

Let vinyl siding preserve the underlying structure of your historic Charlotte property.

If you are fortunate enough to own a historic property in Charlotte that has a wood frame, you are also aware of how labor-intensive wood maintenance can be. Even when using the best of paints, wood siding requires routine inspection and occasional touch-ups if not a complete redo paint job. How do you get around it? Invest in products that can provide exterior protection in a semi-permanent format.

To get the best protection while enjoying the unique treasure of living in a historic Charlotte home, many homeowners install vinyl or aluminum siding as an economical solution that is not detrimental to the current state of the wood. In many cases vinyl siding in Charlotte historic buildings proves to be the best way to fight early signs of deterioration. However, if applied without sufficient planning and consideration “vinyl siding preserves” can become “vinyl siding contaminates.”

Let’s take a look at some important factors to consider and questions to ask before you install aluminum or vinyl siding on your historic Charlotte home.

Be careful not to ignore underlying problems

Before attempting to preserve historic Charlotte properties with wood siding, seek to ensure that you do not conceal problems by merely applying aluminum or vinyl sidings as a coverall. Some problems can go on to affect the very foundations, like water entryways that lead from the roof to the wall and rotting behind the siding were it used to only be a minor problem.

While it may cure pealing paint or the ugly discoloration of the wood, installed vinyl siding on top of such problems can lead to bigger problems – and if moisture is trapped between the barrier and the wood siding you will eventually encounter even bigger problems.

Whereas such possibilities does not mean that you should discount the use of aluminum or vinyl siding preserves, it does mean that you must work with a company that is fully trained in all matters concerning home structures, historic properties, and when and how to rightly install vinyl or aluminum siding.

Durability and Cost To Vinyl Siding Preserve Your Historic Charlotte Property

The inquiries of toughness and relative expenses of aluminum or vinyl siding contrasted with the support expense of notable materials are intricate. Both types of siding offer long life, dependable service and low upkeep. Aside from abuse, quality substitute sidings typically age well even in severe climates. However, time will produce some changes in the shading and gleam of the materials.

Under typical conditions, installation of either component will cost out at several times that of quality paintwork on wood siding. However, the low maintenance and the extended life of vinyl or alum will quickly repay the cost of installation.

A touchy application, holding existing trim, will cost more. Along these lines, to earn back the original investment on cost, the new siding ought to keep going the length of a decades before considering upkeep. On wood two layers of good quality paint on a legitimately arranged surface can last from 8 to 10 years. Let’s say a realist average of seven years is expected for paint on wood, then aluminum and vinyl siding ought to last 15 to 21 years prior to obliging extra upkeep, to earn back the original investment with the support cost for painting wood siding. Once painted, the aluminum and vinyl siding will get repainting with the same recurrence as wood siding.

While aluminum siding can bend upon contact and the effective resistance of vinyl siding gets worse in lower temperatures and, hence, is liable to crack under heavy pressure, these materials are for the most part not any more liable than wood siding and shingles. Every siding material is liable to harm from the elements and potential vandalism; in any case, there is a noteworthy contrast in the repair-ability of wood siding versus substitute materials, for example, aluminum and vinyl. In spite of the fact that they can all be repaired, it is much less demanding to repair wood siding and the repair, in the wake of painting, is for the most part unavoidable. Likewise, a noteworthy issue in the repair-ability of aluminum and vinyl siding, as said above, is getting it to look like the original shade of color it was before it was damaged. Coordinating the paint for wood siding has a more noteworthy probability of matching

Conservation – Energy Efficiency of Vinyl Siding

With the rising cost of oil and gas, it comes as no surprise that the ability to retain energy is an important factor for historic Charlotte wood sidings. This alone makes a big plus concerning the installation of vinyl or alum siding. Although the insulation capabilities built into modern siding materials often include extra thermal backing, on their own vinyl siding preserves are not great insulators. Yet the thermal material, when correctly installed, and the newly added air pocket can offer some slight increase in your homes energy conservation capacities.

For more information, or to schedule your free estimate, contact Right Way Exterior Solutions, LLC, asap.

READ MORE

Fire, Shock, and Leaking Roofs

Leaking roofs increase the structural potential of electrical fire hazards. Even roof leaks that appear minor on the surface can result in serious home damage such as an accumulated growth of hazardous molds, rotted rafters, and even a short in a nearby electrical outlet.

Don’t let minor roof problems magnify into a home or business disaster.

Homeowners often hear promises of a roof lifespan touching 15 to 20 years. And such news leaves one with a feeling of security and peace of mind. Yet total dependence on a written guarantee can sometimes lead to premature roof failure. Never let maintenance of your Charlotte roof slip into the back corners of your mind. When thoughts of repair and maintenance pass through your thinking without provoking personal attention and action, a minor leaking roof can result in major home damage.

You must recognize that wind, trees and animals can cause imminent damage to your home – Damage that is often not covered by the guarantee of the roofer or the maker of the roofing materials.

Some of the causes of a leaky roof include:

  • Leaks around the chimney flashing
  • Missing shingles
  • Accumulated debris
  • Ice dams
  • AND general daily stress from heat, cold, water and ultraviolet rays.

What causes roofs to leak?

The roof on your Charlotte home constantly expands and contracts. In time, the roofing system weakens. We all wish for a permanent roof structure that last as long as the structure of our home, but this doesn’t happen. However, by dealing with roof leaks quickly and efficiency, you can help extend the life of your roofing system.

A leaking Charlotte roof can damage the roof itself as well as the walls, beams, framing, and insulation of your home or business. Furthermore, many of these problems can lead to an accumulation of toxic mold. Also, roof leaks can result in wet floors and other dangers to employees and family members.

Some people never go up into their attics. Thus they have no idea what is up there. Some Charlotte homeowners also use their attic as a spare bedroom, computer room, or exercise and hobby room. Many people use their attic as a place to store junk. As a result, many attics include electrical outlets, fans and any number of small electrical devices that could all be damaged by water dripping from the ceiling. And we all know that uncontrolled water and electrical components can be a lethal combination as well as an ongoing fire hazard.

For rapid professional help with your Charlotte leaking roof problems, contactRight Way Exterior Solutions.

READ MORE

Clogged Gutters Among Common Causes For Charlotte Home Wood Rot

Despite all efforts taken to protect your Charlotte home from rotting wood, in all likelihood some measure of decay fungi is currently at work on your home. It can happen anytime and anytime and anywhere, even on new homes. And it is not limited to outdoor decking or other exterior areas that come into regular contact with water. Moisture can find its way into the most inconspicuous places. If you haven’t recently cleaned and secured your roofing drainage system, clogged gutters may at this very moment be a breeding ground for wood rotting fungi.

The first signs of rot or decay usually show up in the form of cracks or at seams where two pieces of wood meet. Rot is most commonly discovered along the trimmings of doors, window frames, windowsills, and etc. Caused by minute fungi, wood decay can become one of the most expensive home repairs in your budget. And even though the fungi are mere microscopic threads, noticing a cluster is rather easy. Not all fungi induce wood decay, but all should be treated as quickly as possible. This means you must:

  • Eliminate the cause
  • Repair the damage
  • AND take reliable preventive measures to stop future occurrences.

Replacing clogged gutters is expensive, but not near so costly as repairing rotted fascia, soffit, rafters and other exterior and interior Charlotte home roofing components is far more costly. Better still: Clear your gutters and install a reliable gutter guard system.

Repairing Wood Rot

The process of repairing wood rot can be a bit too involved and possibly too dangerous for the average homeowner. If you’ve only performed basic home repairs, you may be better off hiring a home repair contractor. In order to prevent water from re-entering affected areas, the pros work with special wood epoxy products. First the wood rotted surface needs to be removed completely. Second, the putty-like wood epoxy is filled in and sanded down to the appropriate size.

When it becomes too difficult to remove all of the wood rot, there is an alternative product known as a “consolidant.” This material is injected into the fibers of the wood using a highly advanced liquid compound, which reinforces the infected wood. Rightly applied “consolidant” essentially replaces the damaged portion of the wood with a higher density and water-resistant material. In order for “consolidant” to perform as expected, rotted wood must be completely dried out before work begins.

If you do decide to undertake this repair on your own, be very careful when utilizing these epoxy formulas. They can cause very serious skin damage and are toxic when inhaled. These industrial-strength super glues will also ruin any surface that they were not intended to come in contact with.

Preventing Future Wood Rot

No matter how well the repair goes, if you don’t fix the problem creating the symptom in the first place, then you’ll just end up with wood rot sometime again in the future. Check all cracks and trimmings that have caulking, make sure the seal is strong, or replace it with acrylic latex caulking. Problematic plumbing or fixtures may also need attention if the wood rot is located nearby. Moisture can travel some distance if there is a leak that can run along a compromised seal or cracking. Replacing of any moldings with more water-resistant versions in the kitchen, bathrooms, or laundry rooms can also keep moisture in-check. If poorly installed or clogged gutters are causing the problem, that too must be corrected.

Further Considerations

If your experience with leaks and wood rot is one with extensive history, it might be worth investing in new pressure treated wood solutions for the outside as well as the inside the home. Borates have been discovered to be a safe, non-toxic solution to protecting your wood, and this solution can be applied as simply as using a spray-attachment on your garden hose. Borates is an all-natural mineral solution that coats the wood to prevent moisture from entering, as well as borrowing insects like termites and carpenter ants.

If you need additional information, gutter cleaning or any other guidance, contactRight Way Exterior Solutions. From roofing to siding, and all the in-betweens, we have a thirty-plus year history of providing quality Charlotte home exterior repairs and installs.

 

READ MORE

Ice Dams: Which Comes First, the Law of Gravity or an Unstable Roof?

Before dipping into the depths of this particular Charlotte roofing tip, Zimmerman Enterprises Kanga Roofing of Charlotte would like you to consider a strange phenomenon concerning ice dams: Water doesn’t always flow down hill. At times it backs up, accumulates and only then submits to the power of nature and gravity. The result may be a slow trickle that can be addressed and managed before major structural damage can accumulate. Or…

The submission to gravity may force your roof leak to explode with devastating and costly consequences to your home and to your health.

Ice dams can make water flow uphill. So too can clogged drains, gutters and downspouts. Back in 2006 while reconstructing the old Charlotte IRS building, a local Metrolina construction company encountered a major leak issue (1). It came about shortly after a summer downpour dumped inches of water throughout Mecklenburg. Within the hour, stories of flash floods, structural damage and leaky roofs dominated the news.

Next morning in the old IRS building on Albemarle Road, water leaks had sprung up all across the southeastern wing of the structure. Rather than mere drips, the leaks were like minor springs of continuous water flow. Ceilings, walls and carpets got damp, then soggy and then ruined. Repair costs mounted quickly as did material requirements.

When work crews reached the roof of the building, they discovered knee-deep water in all the lower sides of the flat roof building. Three roof drains were completely stopped up. The water pressure had backed up, amassed pressure and then forcibly found new ways for obeying the law of gravity.

Having a sturdy roof is essential to home protection from the weather and from the elements. To maintain the stability of your roof unhampered water drainage is an absolute necessity. You need to know how and when to check your roof. Regular roof inspections ensure that rainfall, sleet and ice do not backup, build up and eventually explode beneath the overwhelming law of gravity.

Ice Dams and Charlotte Roofing Tips For Reliable Prevention

Although often used in office and industrial construction planning, flat roofs are not standard on residential Charlotte homes. Most of you live in “A” frame structures. You have asphalt shingled or metal roofs – sometimes tile or wood shakes. Thus ice dams can be a common problem.

According to the University of Minnesota, the ridge of ice that accumulates at the edge of your roof is called an ice dam (2). Every article with a focus on Charlotte roofing tips mentions the roofing dangers associated with backed up water. When an ice dam prevents melting show from draining off your roof, the water temporary flows up hill. As a result of the backup, water eventually begins to seep, leak or explode into your home. The damage to your Charlotte residence can include structural collapse of the roof, ceilings or drywall. The accumulated damage associated with ice dams also includes wet attic insulation, electrical shorts and even exterior wall damage.

Stopping water leaks is critical to the stability of your roof and the protection of your Charlotte home. Preventing water from flowing uphill is one component of proper roof management. Don’t risk the dangers of ice dams, water backup and explosive leak damage. Act now to correct known problems in advance of the coming winter snows.

Even when explosive and immediate damage doesn’t occur, rainwater under your shingles results in long-term roof rot. Even when melting snow doesn’t create a technical “ice ridge,” trash in your gutter can result in blockage, refreezing and water backup. High winds sometimes lift shingles. Debris gets forced underneath. When the rain falls the wind forces the water into the gaps.

Preventing the Ice Dams and Ice Dam Damage

To prevent roof damage due to ice dams, follow two courses of action: 1) Immediate response to the situation and 2) Long-term solutions.

Immediate ice dam prevention demands that you get the snow and ice off your roof. In order to prevent shingle damage, use a push broom or a roof rake. But be very careful, for your own safety and for the safety of your existing roofing materials. If water is already flowing into your home, break channels in the ice dam. It’s a touchy job. Consider hiring a professional Charlotte roofing contractor.

Long-term ice dam solutions require special considerations. Start by eliminating any interior leaks of warm air into the attic. Moist interior heat on the inside of your roof structure promotes melting and refreezing of snow and ice. Have your attic inspected by a professional Charlotte roofer. Adding ceiling/roof insulation may eliminate all of your leakage problems related to ice dams. Don’t forget to repair the existing roof damage.

Zimmerman Enterprises is always on hand to provide you with free estimates on any full-home roof replacements or roof installations.

VISIT: https://rightwayexteriorsolutions.com/

READ MORE